?????????? ??? ? to220 ? ???? ??? ??? ???. 1 ??? ?????? ???. - 120 v ac ????? ???? - 10,2 x 4,6 x 30 ? ????? ??? ? 3 , 6 ???? ?? - 723 - 118 6 ?????????? u ?, () i ?, (a) ??? ?? ?? ?? ?? ??? ??? c ?? ?? ?? ??? c bt - 67l090 (juc - 31f - 90 - d) 120vac/48vdc 1 nc ( ?. ??? ) 90 4 60 4
6700 series standard temperature calibrations operate ( 5 c) 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 reset (min c) 20 20 30 30 40 40 50 50 55 55 60 60 70 70 80 80 85 85 90 differential (min c) 4 4 4 4 4 4 4 4 6 6 6 6 6 6 6 6 9 9 9 how to use this chart each thermostat part number consists of functional ?uilding blocks?to enable the user to specify clearly and precisely the desired characteristics in each category. select the proper code in each category, then transfer it to the box indicated. unless a special requirement is indicated, the part number will be complete when the proper temperature is selected. if you have a special re quirement, please call airpax fo r a factory assigned number to complete the part number. example: a 67f060 thermostat will close (make contact) on a rising temperature from 55? to 65? and will reset (break con- tact) on a falling temperature no less than 4? lower than the actual close temperature and no lower than 40? actual temperature. specifications contact resistance: 50 milliohms max. (before and after rated life) contact ratings: cycles voltage amps (resistive) 30,000 48 vdc 1 30,000 120 vac 1 1 00,000 5 vdc .020 1 00,000 5 vdc .001 contact operations: either open on rise or close on rise operating temperature range: 40? (104?) to 130? (266?) standard operating temperature tolerance: 5? ( 9?) nominal operating temperature settings in 5? (9?) increments us patent no: 4,795,997 short term exposure limit: 260? (500?), 10 sec. long term exposure limit: -55? (-67?) to 160? (320?) dielectric strength: 1480 vac 60hz, 1 second terminals to case for nickel-plated copper bracket. 2000 va c 60hz, 1 second terminals to case for plastic bracket. insulation resistance: 1 00 megohms at 500 vdc contact bounce - make: 3 ms max. wei ght: approximately 0.5 grams seal: epoxy sealed for wave soldering and cleaning. moisture proof per airpax spec. s-722 (unit will not leak while submerged in 9 " of water for a minimum of two minutes). vibration: p er mil-std-202, method 204d, te st condition d, 10-2,000 hz. shock: p er mil-std-202, method 213,test condition c, 1 00 g s, 6 milliseconds, ?/? sine wave. chemical resistance: unit is resistant to water, salt, alcohol, ammonia, trichlorethane, and most other organic solvents. solderability: t erminal material is selectively striped with 60/40 solder for improved solderability. r esistance to soldering heat: p er mil-std-202f, method 210a,test condition e. file numbers: ul recognized e36687 csa certified lr25561 vde approval 11624, 2-4510-1004 (plastic bracket only) materials seal: high temperature epoxy base: pps (polyphenylene sulfide), 94 vo rated te rminals: 65% copper, 18% nickel contacts: gold-plated or overlay, silver cross bar bracket: nickel-plated copper or high pressure laminated plastic ( .706 ) 1 7.9 ( 1 4.35 ) .565 ( 5.49 .13 ) .216 .005 ( 3.640 .089 ) .1435 .0035 dia ( 2.79 .13 ) .110 .005 ( 5.08 .13 ) .200 .005 ( 1 0.16 .13 ) .400 .005 ( .76 .08 ) .030 .003 ( 5.08 .25 ) .200 .010 ( 1.27 .10 ) .050 .004 ( .330 .013 ) .0130 .0005 ( 2.79 .13 ) .110 .005 ( 6.35 .50 ) .250 .020 ( .76 .025 ) .030 .001 ( 4.70 .25 ) .185 .010 ( 29.59 0.74 ) 1.165 0.029 ref ref basic product series contact operation f = fan ( close on rise ) l = limit ( open on rise ) operating temperature in c ( from table, above ) mounting bracket designation: ?lank?for nickel-plated copper bracket ??for plastic mounting bracket ( vde approved) factory assigned number f or special requirements 67 065 lp 0655 schematic at 20 c ( open on rise ) ( case isolated from terminals ) schematic at 20 c ( close on rise ) ( case isolated from terminals ) airpax 6700 series thermostats the mounting bracket designation and the 4 digit manufacturing nu mber are used for ordering special features and may not ap pear as part of the marking on the thermostat. te mperature set point calibration is checked at airpax with precision test equipment and proven meth- ods. because customer checking methods may differ, a typical variance allowed for correlation is ??.
|
